lindsay Posted October 5, 2014 (edited) anyone here know were I could source spiral dowels from? looking for a 1000 or so. Edited October 5, 2014 by lindsay 1 Share this post Link to post Share on other sites
theuserformallyknownasd00d Posted October 5, 2014 Great question! I've inquired at the big hardware retailers to no avail Share this post Link to post Share on other sites
Matt1208 Posted October 5, 2014 ive seen some on amazon before but i gather postage would be a bit pricey coming from overseas Share this post Link to post Share on other sites
waterboy 2.0 Posted October 5, 2014 (edited) Not common at all in Australian wood/timber trades, we generally use plain or fluted dowels or biscuits on a lot of panels now. I could never find spiral cut dowel rods or dowels. Remember wood /timber is not usually quarantine friendly, unless going through entry treatments ( = $cost). They can be made on a bandsaw if you are good on the tools. You'll need a tilting table though and mitre guard/custom jig. Guard/jig controls the depth of cut, tilt the table down from the teeth (easier to spin rod), then wind the rod back to get the spiral. Get it jigged up right and it doesnt' take long to smash the rods out, then cut em up could also use a lathe, but there is more mad skills to pull that one off without breaking the dowel rod. Edited October 5, 2014 by waterboy 1 Share this post Link to post Share on other sites
zelly Posted October 5, 2014 spiral dowels are all over ebay & appear to be stocked by most Home Depot stores (usa) this guy claims to ship world wide..... http://www.ebay.com/itm/One-Pound-600-or-Mushroom-Plugs-Dowels-5-16-x1-8-25mm-Spiral-Grooved-NEW-/120905868952?pt=LH_DefaultDomain_0&hash=item1c268d2698 Share this post Link to post Share on other sites
lindsay Posted October 6, 2014 importing wood dowels would have customs jumping up and down, and treatment would mean chemicals. I think I will go with fluted dowels. I am looking at some Tasmanian oak, 500 for 20 bucks. cheers everyone. Share this post Link to post Share on other sites
waterboy 2.0 Posted October 6, 2014 500 for $20 is a bargain If you're on a good source I'd like a piece of that action...lol seriously if you can get cheaper for a larger lot I am in....... Share this post Link to post Share on other sites
lindsay Posted October 7, 2014 just pm the dowel supply site to you Waterboy . there supply looks low so I didn't post here, its first in best dressed. post here, if there is any left after you buy. 20 bucks seems a good price. this will be the first time using dowels. I got access to a heap of poplars between 6-10 inches dia. so I am having a crack at it with a few species. Share this post Link to post Share on other sites
waterboy 2.0 Posted October 7, 2014 (edited) Thanks Lindsay, on checking them out they are fluted ones, they will kinda work but its a fine line when you are tapping them into logs. I am gunna have to keep making them ghetto style until someone finaly does production spirals...lol...which is a pain in the arse EDIT -I've found you can colonise suitable fluted dowels , its hit and miss after you hammer them in the speed or even success of getting them to leap of into the sapwood. Frustrated the shit outta me..... Edited October 7, 2014 by waterboy Share this post Link to post Share on other sites
theuserformallyknownasd00d Posted October 7, 2014 Would it work just as well WB if you drilled the hole a fraction bigger than the fluted dowel? And plugged up as usual..? Or is there just not enough surface area for the myc to grab ahold of and be slot in? Share this post Link to post Share on other sites
waterboy 2.0 Posted October 7, 2014 I am not really sure why, I think too much damage to the myc when tappin in. My theory is the spiral is more protective of the myc (?) The dowel should need 3-4 light taps tops IMO. You really want that wood contact. I've found for shiitake sawdust plug worked better than fluted, spiral was king. Fluted ones just haven't given me the speed and consistency of sapwood myc run for shiitake That said someone else might find a better method, i'll keep making spirals outta rods when I need them. I tried to spiral fluted ones...but small fiddly dowels are not easy to smash out a fair number 2 Share this post Link to post Share on other sites
lindsay Posted October 7, 2014 (edited) I am thinking of making a jig, to drop say 6 or so dowels in and then drilling a hole through the side of the dowels at top 1/3 to meet the cambium layer. maybe several holes? Edited October 7, 2014 by lindsay Share this post Link to post Share on other sites
Zen Peddler Posted October 8, 2014 There was a guy selling these back in 2003 or so in Australia. Ill see if I can find his detail. If I remember they were poplar or something obscure. Share this post Link to post Share on other sites